教您選購排線器

如果您不知道您要用的排線器長度，下圖可幫助您

例如：你的收線盤假如是300的寬度，那就是300 排線器寬度90=390在加間隙40--60您應選用有效內開450的就可以了。圖上所標數據是本公司的標準圖紙，如果您看不清楚我可以給您發詳細的資料，您也可提供您的圖紙，按照您的要求生產?；蛘吲南聲r(shí)留言說明內開就可以了。

下圖是內開400的示意圖

下圖是我公司的圖片介紹

本公司2005年建造的辦公大樓

我公司擁有先進的加工設備，每臺價值近50萬元的立式加工中心，一次編程可加工排線器零配件10件，大大提高了速度也降低了生產成本，還能保障產品的質量與精度。

本公司倉庫一角

使用前請認真閱讀本說明書

Please read this manual carefully before you use the machine.

從主機拉出來的線經過排線器頂部的導線輪（筒）纏繞在收線盤上，光桿的動力較好由收線軸傳給，其速比可根據用戶需求自行配比，一般應在1:1~1:5范圍內。光桿排線器的動力也可單獨設計，特殊情況下，也可使排線器帶動收線盤運動，從主機放出的線不動。

排線器帶動線纜行走到收線盤邊緣時，換向臂上碰輪即碰到定位塊實現瞬間換向，時間不超過一秒。

適用于1200轉/分高速工作，滿足于往復運動極為頻繁的場合。

The wire drawn from the main frame is wound up onto the take-up reel through the wire guide pulley/pipe over the Traversing Drive. It’s recommended the plain shaft be powered by the shaft of the take-up reel, and the speed ratio can be set according to customer’s requirement, typically in the range of 1:1~1:5. The dynamic force of the plain shaft Traversing Drive can be designed independently. In a special case, the take-up reel can be powered by the Traversing Drives while the wire released by the main frame is immobile.

When the Traversing Drive guides wire/cable onto the edge of take-up reel, the trigger roller of the reversal arm snap the end stop, by which the instantaneously reversal is realized, in 1 second or less.

Applicable to the high speed condition of 1200 rpm and where the reciprocating movement occurs frequently.

排線器應用示意圖

Application Diagram of the Traversing Drive

GP15~60型排線器安裝調試

Installation and Adjustment of Traversing Drives GP15~60

光桿轉向

Direction of Shaft Rotation

光桿一定要旋轉串入機箱，防止與機箱兩端防塵板發生碰撞。光桿表面硬度HRC50-62，光潔度0.8、直徑偏差